Építés alatt – nem éles oldal
Belépés
Fut, nem toborozFázis nélkül

3D Printed vs Ready-to-Wear Insoles for Diabetic Neuropathy

A legfontosabb adatok

Ki végzi
University of Faisalabad
Hol
Pakisztán1 helyszín, 1 országbanVálassz országot a helyszínekhez
Azonosító
Állapot
Fut, nem toboroz
Résztvevők
22 fő, tervezett
Kezdés
2026. jan. 1.
Befejezés
2026. júl. 15.
A vizsgálat típusa
Beavatkozással járó, 2 csoportAz egyik csoport egy már használt kezelést kap, összehasonlításként.
A vizsgált kezelések
  • 3D Printed Customized Insole
  • Ready-to-Wear Insole
A regiszteradat frissítve
2026. június 17.

Ki vehet részt

Életkor
35 év – 65 év
Nem
Nők és férfiak
Egészséges önkéntesek
Nem vehetnek részt

A regiszter feltételei, szó szerint

Mind a 16 feltétel megnézéseKevesebb

Ki vehet részt

  • Age 35 to 65 years
  • Diagnosed with diabetes mellitus
  • Clinical diagnosis of diabetic peripheral neuropathy
  • Ability to walk independently without walking aids
  • Normal cognitive function
  • Corrected or uncorrected vision sufficient for safe ambulation
  • Willingness to provide written informed consent

Ki nem vehet részt

  • Presence of active foot ulcer
  • History of lower limb surgery within past 6 months
  • Peripheral vascular disease
  • Neuromuscular diseases (e.g., stroke, Parkinson's disease, multiple sclerosis)
  • External wound on lower extremity
  • Major lower limb amputation
  • Foot drop
  • Charcot arthropathy
  • Inability to comply with study protocol

Hol van ez a vizsgálat?

Egy országban van helyszíne. Válassz országot, hogy lásd a helyszíneket.

A vizsgálatról

Mit akar kideríteni a vizsgálat

Diabetic neuropathy is a condition caused by chronic high blood glucose levels that damage nerves over time, frequently causing abnormal plantar pressure and increasing the risk of foot ulcers and impaired mobility. Insoles are widely used to redistribute pressure and improve comfort. This study compares the effect of 3D printed customized insoles versus ready-to-wear insoles on plantar pressure changes in patients with diabetic neuropathy. The study is a randomized controlled trial with 22 participants randomly allocated to two groups: one receiving 3D printed customized insoles and the other receiving ready-to-wear insoles. Plantar pressure is measured using piezoresistive sensors and an Arduino Nano Unit. Secondary outcomes include foot health status (FSHQ questionnaire), satisfaction with assistive technology (QUEST 2.0), and neuropathy severity (NSS and NDS questionnaires). Assessments occur at baseline, 4 weeks, and 8 weeks.

A vizsgálat 2 csoportja

  • Group A: 3D Printed Customized InsolesA vizsgált kezelés

    Participants in this group receive 3D printed customized insoles tailored to individual foot morphology. Insoles are designed to provide arch support and gait alignment. Participants wear insoles for minimum 6 hours/day, 5 days/week for 8 weeks, following a phased protocol of acclimatization, pressure adaptation, and function improvement.

    Kezelés: 3D Printed Customized Insole és Ready-to-Wear Insole

  • Group B: Ready-to-Wear InsolesMár használt kezelés, összehasonlításként

    Participants in this group receive prefabricated ready-to-wear insoles providing general cushioning and basic support. Participants wear insoles for minimum 6 hours/day, 5 days/week for 8 weeks, following the same phased protocol as the experimental group.

    Kezelés: Ready-to-Wear Insole

Adatok és források

Regiszteradat
Szerepel a ClinicalTrials.gov-on.
Hivatalos cím
Comparative Effect of 3D Printed Customized Insoles and Ready to Wear Insoles on Plantar Pressure Changes in Patients With Diabetic Neuropathy
A regiszteradat frissítve
2026. június 17.